
GeekVape
GeekVape P Series Coils (B100 / Aegis Boost Pro Coils)
$11.95
GeekVape P series mesh coils in 0.2Ω and 0.4Ω, sold by the pack. They fit the B100 (Aegis Boost Pro 2), the Aegis Boost Pro, the E100 and the E100i.
- P0.2Ω and P0.4Ω mesh, sold by the pack
- Anti-spitback core keeps the tip clean
- Fits the B100 and Aegis Boost Pro
Step 1 of 1: choose Resistance to continue
Limit 5 per order. Need more? Request a larger quantity.
- Resistances
- 0.2Ω, 0.4Ω
- Wattage
- 50–70W
- Coil type
- KA1 mesh
- Fitting
- Push-in
- Draw style
- Direct lung / restricted lung
- Sold as
- By the pack
GeekVape P Series Coils are the push-in mesh coils for GeekVape's bigger pod mods. A pod mod is a pod vape with a screen and power that you can adjust. These fit the B100 (Aegis Boost Pro 2), the original Aegis Boost Pro and the E100 (Aegis Eteno) kits. Every GeekVape P coil has a kanthal (KA1) mesh and an anti-spitback core, which keeps hot e-liquid from popping up through the mouthpiece. The mesh is a thin metal screen, and it makes warm, dense vapor. These are sub-ohm coils, which means they're under 1 ohm and made for bigger clouds. We carry the two P coils that most vapers use, the P0.2Ω and the P0.4Ω, and we sell them by the pack.
- Two P series mesh coils: the P0.2Ω (60–70W) for clouds and the P0.4Ω (50–60W) for a slightly tighter draw
- KA1 mesh with a built-in anti-spitback core
- The coil for the B100 pod in our GeekVape Aegis replacement pods
- Push-in fitting, so there are no threads to mess with
- These aren't B series coils. The Aegis Boost, B60, Hero and Boost 3 take Boost Mesh coils
What's in the Box
- 1 pack of GeekVape P series mesh coils in the resistance that you pick
- Made for the B100, Aegis Boost Pro and E100 pod mods
- Coils only. Pods and devices are sold separately
GeekVape P Series Coil Specs
| Spec | GeekVape P Series Coils |
|---|---|
| Resistances we stock | P0.2Ω and P0.4Ω mesh |
| Wattage | P0.2Ω 60–70W · P0.4Ω 50–60W |
| Heating element | KA1 (kanthal) mesh |
| Features | Anti-spitback core |
| Fitting | Push-in, no threads |
| Sold as | By the pack |
GeekVape P Coils: Resistance & Wattage
Both P coils are mesh. The P0.2Ω is a full direct-lung coil, which means the vapor goes straight to your lungs. The P0.4Ω runs a little cooler, and it works well with a restricted lung draw, which is in between mouth-to-lung (like a cigarette) and direct lung.
GeekVape also makes a P0.15Ω XM and a P0.5Ω coil. We don't carry those right now, but please request them, and we'll do our best.
Will P Series Coils Work With My Device?
- GeekVape B100 / Aegis Boost Pro 2 (B100 pod)
- GeekVape Aegis Boost Pro (original)
- GeekVape E100 (Aegis Eteno) and E100i
- GeekVape Obelisk 60 (P0.4Ω only)
- GeekVape B21700 and XP77, per GeekVape's coil guide
- Aegis Boost, B60 (Boost 2), Boost 3, Boost Plus and Hero kits use Boost Mesh coils
- GeekVape P Sub-Ohm Tank and Zeus tanks need Z series coils
- Aegis Nano, Wenax and other built-in-coil pods
Need a new B100 pod too? Just pick the "B100 pod" option on our GeekVape Aegis replacement pods page.
Best Vape Juice for P Series Coils
With P coils, we recommend freebase, which is just the regular kind of nicotine, and we always like to suggest 3 to 6mg. At 50–70W, MAX VG works best, and 50/50 is usually fine in the P0.4Ω, since it runs at a lower wattage. VG (vegetable glycerin) is the thicker base liquid, and it's what makes the vapor. Here at Custom Blend Vape Juice, we mix your freebase vape juice by hand after you order it, in the exact strength that you want. If you're still deciding on a flavor, a vape juice sample pack lets you try five different ones first.
Custom Blend Tip: P and B series coils look a lot alike, so check the letter printed on your old coil before you swap in a new one. A B series coil won't fit your B100 pod.
How to Change & Prime a P Coil
- Take the pod out of the device, and pull the old coil straight out of the bottom.
- Prime the new coil. Drip 3–4 drops of e-liquid into the top of it and onto the cotton.
- Press the new P coil firmly into the pod, and then fill the pod.
- Let it sit for at least 10 minutes, so the cotton can soak all the way through. The longer, the better.
- Start around 50W on the P0.4Ω or 60W on the P0.2Ω. Take a few drags, and then slowly work your way up from there.
P Series Coils Reviews
- Flavor & vapor: the KA1 mesh makes warm, thick clouds, and that's a lot of vapor for a device this size.
- Spitback: the anti-spitback core keeps the drip tip (the mouthpiece) cleaner than older pod coils do.
- Look out for: P and B series coils look alike, so check the letter printed on the coil before you buy.
P Coil Troubleshooting
- "No atomizer": push the coil all the way into the pod, and wipe off the pod's contacts.
- Burnt taste on a new coil: let it prime longer, and start at the low end of the range.
- Leaking from the bottom: usually the coil isn't fully seated, or its O-ring (the little rubber seal) is torn or nicked.
- Weak flavor: the coil is worn out. It'll start putting out less vapor, and the flavor will taste a little muted. Most vapers change P coils every 1–2 weeks.
Questions & Answers
What devices do GeekVape P series coils fit?
They fit the B100 (Aegis Boost Pro 2), the original Aegis Boost Pro, and the E100 (Aegis Eteno) and E100i. The P0.4Ω also fits the Obelisk 60, and GeekVape lists the B21700 and XP77 too.
What coils does the GeekVape B100 use?
P series coils. The B100 is the Aegis Boost Pro 2, and its pod takes both the P0.2Ω and the P0.4Ω.
Are P series and B series coils the same?
No. B series (Boost) coils fit the Aegis Boost, B60, Boost 3 and Hero kits, and P series coils fit the Boost Pro and B100. They look alike, but they aren't interchangeable.
Do P series coils fit the GeekVape P Sub-Ohm Tank?
No. It sounds like it would, but the P Sub-Ohm Tank takes GeekVape Z series coils.
Which P coil should I choose?
We'd recommend the P0.2Ω (60–70W) if you like an open direct-lung draw and more vapor. The P0.4Ω (50–60W) gives you a slightly tighter, cooler draw, and it's a little easier on juice.
What wattage is the GeekVape P coil 0.4?
GeekVape rates the P0.4Ω at 50–60W.
Can I use nicotine salt with P coils?
We don't recommend it. These coils run at 50–70W, and nic salt, the smoother nicotine made for low-power pod kits, would be way, way too much nicotine at that power. We recommend freebase in 50/50 or MAX VG instead. We always like to suggest 3 to 6mg.
How long do GeekVape P coils last?
It all depends on how much you use them, but most people get 1–2 weeks of daily use. Prime each one well and go easy on very sweet juice, and they'll last longer.
For use by adults 21+.
| Compatible with | GeekVape B100 (Aegis Boost Pro 2), Aegis Boost Pro, E100 (Aegis Eteno), E100i and Obelisk 60 (0.4Ω only) |
|---|---|
| Resistances | P0.2Ω Mesh (60–70W), P0.4Ω Mesh (50–60W) |
| Sold as | By the pack |
| Tip | Drip a few drops of juice on a new coil and give it at least 10 minutes to soak before you vape. |
See our Shipping Policy and Returns.
You May Also Like
Customer Reviews
We just relaunched our website, so our reviews got a fresh start too. Own one of these? We'd love for you to be one of the first to share your thoughts!




